Raspberry Pi Email Server Part 2: Dovecot

Powered by Drupal
Submitted by Sam Hobbs on

Dovecot Logo This is the second part of a five part tutorial that will show you how to install a full featured email server on your Raspberry Pi. This tutorial covers Dovecot, which provides SASL authentication and IMAP capabilities.

The parts are:

The Introduction & Contents Page (read first)

Raspberry Pi Email Server Part 1: Postfix

Raspberry Pi Email Server Part 2: Dovecot

Raspberry Pi Email Server Part 3: Squirrelmail

Raspberry Pi Email Server Part 4: Spam Detection with Spamassassin

Raspberry Pi Email Server Part 5: Spam Sorting with LMTP & Sieve

Fixing the errors that appeared during dovecot installation

In part 1, when you installed Dovecot I mentioned that you might see some errors like this:

Creating config file /etc/dovecot/conf.d/20-imap.conf with new version
[....] Restarting IMAP/POP3 mail server: dovecotError: socket() failed: Address family not supported by protocol
Error: service(imap-login): listen(::, 143) failed: Address family not supported by protocol
Error: socket() failed: Address family not supported by protocol
Error: service(imap-login): listen(::, 993) failed: Address family not supported by protocol
Fatal: Failed to start listeners
 failed!
invoke-rc.d: initscript dovecot, action "restart" failed.
dpkg: error processing dovecot-imapd (--configure):
 subprocess installed post-installation script returned error exit status 1
Setting up dovecot-ldap (1:2.1.7-7) ...

These errors are caused by the lack of IPv6 support, which I mentioned in the previous tutorial. To remove the errors, open the main dovecot configuration file (/etc/dovecot/dovecot.conf) and find this line:

listen = *, ::

And change it to:

listen = *

The * means “all IPv4 addresses”, the :: means “all IPv6 addresses”. Now restart Dovecot, and you shouldn’t get any errors:

sudo service dovecot restart

Note: since I wrote this tutorial, there have been a few small changes to the default configuration file - you may find that the line is commented (with a # at the start of the line). If so, remember to uncomment it when you make your changes!

Tell Dovecot where your Mailbox is

Open /etc/dovecot/conf.d/10-mail.conf and find this line:

mail_location = mbox:~/mail:INBOX=/var/mail/%u

Change it to this:

mail_location = maildir:~/Maildir

Instruct Postfix to use Dovecot SASL

Now we need to tell Postfix that we would like to use Dovecot for SASL authentication. Open /etc/postfix/main.cf and add these lines:

smtpd_sasl_type = dovecot
smtpd_sasl_path = private/auth
smtpd_sasl_auth_enable = yes

Now tell Dovecot to listen for SASL authentication requests from Postfix. Open /etc/dovecot/conf.d/10-master.conf and comment out the current block that begins with service auth (place a # at the start of each line). Replace it with this:

service auth {
        unix_listener /var/spool/postfix/private/auth {
                mode = 0660
                user = postfix
                group = postfix
        }
}

Now you want to enable plain text logins. Do it by adding these two lines to /etc/dovecot/conf.d/10-auth.conf. Make sure they are not already present in the file, or your settings may be overwritten with the default ones if the default is declared later in the file than the lines you add. If the parameters are already present, you can either modify the existing lines or comment them out and add these new ones:

disable_plaintext_auth = no
auth_mechanisms = plain login

Note that although the logins are in plain text, we will be setting Postfix up later so that it only allows you to use plaintext logins from within SSL/TLS. This means that your login and password will sent in an encrypted session - you wouldn't see them in plain text if you used a packet sniffer, for example. For now, we’re allowing unencrypted plain text logins so that we can test logging in with Telnet. Since the connection is local (from the Pi to the Pi), your password isn’t being sent over any insecure networks so this is fine.

Testing SASL

Creating a new user for testing purposes is a good idea. Let’s call this temporary user testmail and give it the password test1234 Use this command to add the user, and follow the prompts including setting a password.

sudo adduser testmail

Now restart Postfix and Dovecot:

sudo service postfix restart
sudo service dovecot restart

We’re now going to try and send an email after authenticating with SASL. The server is expecting to see a base64 encoded version of your username and password, so we have to convert it first. There are three ways of doing this, so I've given examples below using the testmail username and test1234 password:

#Method No.1
echo -ne '\000testmail\000test1234' | openssl base64

#Method No.2
perl -MMIME::Base64 -e 'print encode_base64("\0testmail\0test1234");'

#Method No.3
printf '\0%s\0%s' 'testmail' 'test1234' | openssl base64

I have discovered that if your password starts with a number, methods 1 and 2 don’t work. Assuming the username and password are testmail and test1234, the commands produce this:

AHRlc3RtYWlsAHRlc3QxMjM0

WARNING: If you’re having problems with authentication and you paste examples to forums or mailing lists, be aware that it is really easy to convert this back into your username and password (hence the creation of a test user). If you're using your real username and password to test, redact it before posting! Now, still logged into the Pi via SSH, you can telnet port 25 to test whether or not SASL is working. There’s only one extra step, which is the AUTH PLAIN command that comes after ehlo but before mail from. For testing, the permit_mynetworks parameter should be commented out under your postfix smtpd_recipient_restrictions block in /etc/postfix/main.cf. If you’re following on from Raspberry Pi Email Server Part 1: Postfix then this should already be the case. If you have to change it, remember to reload postfix (sudo service postfix reload) after you change the value. Here’s an example:

telnet localhost 25
Trying 127.0.0.1...
Connected to localhost.
Escape character is '^]'.
220 samhobbs ESMTP Postfix (Debian/GNU)
ehlo facebook.com
250-samhobbs
250-PIPELINING
250-SIZE 10240000
250-VRFY
250-ETRN
250-STARTTLS
250-AUTH PLAIN LOGIN
250-ENHANCEDSTATUSCODES
250-8BITMIME
250 DSN
AUTH PLAIN AHRlc3RtYWlsAHRlc3QxMjM0
235 2.7.0 Authentication successful
mail from:testmail
250 2.1.0 Ok
rcpt to:me@externalemail.com
250 2.1.5 Ok
data
354 End data with .
Subject: This is my first email that has been authenticated with Dovecot SASL
Woop woop
.
250 2.0.0 Ok: queued as B87133F768
quit
221 2.0.0 Bye
Connection closed by foreign host.

Now try again but enter the username/password incorrectly (base64 encode something random) – you should get an error message and the email won’t send. If everything went to plan, then SASL is working properly! You can now uncomment permit_mynetworks again.

Separating Incoming email (unauthenticated) from Outgoing Email (SASL authenticated)

It’s probably a good idea to have a dedicated port for sending outgoing email…here’s why: Port 25 doesn’t require (but does offer) SSL/TLS encryption. If you mess up configuring your mail client you could end up letting it authenticate with SASL over insecure connections. Using a different port that only accepts SSL/TLS connections removes the risk that a poorly configured email client could be sending your password unencrypted over dodgy networks. There are two ports you can use for this:

  1. 465: SMTP over SSL
  2. 587: Email submission

587 is the “official” port for email clients (like K9 mail, Thunderbird and Outlook) to use when submitting messages to the Mail Submission Agent (your email server) – the submission may be encrypted or unencrypted depending on the server configuration. 465 was a port that was assigned for SMTP with SSL/TLS before the STARTTLS protocol was introduced, back in the days when you chose your port and that decided on the type of connection you were going to get (encrypted or unencrypted). STARTTLS changed things because it allows you to connect with an unencrypted connection (like the one you get with Telnet), and then upgrade to an encrypted connection without changing port… so when STARTTLS was introduced, SMTPS on port 465 was removed from the standard because you could do the same thing with a single port (25). However, I think there is some value in specifying a port for submission that only accepts SSL/TLS encrypted connections, and won’t work if the connection isn’t encrypted. This means that if you misconfigure your email client it just won’t work, instead of working and sending your password in an unencrypted format. So, anyway… Here’s how to set up Postfix to listen on port 465 for encrypted connections. The first step is telling Postfix to listen on port 465, so open /etc/postfix/master.cf and uncomment the line:

smtps     inet  n       -       -       -       -       smtpd

Now restart Postfix:

sudo service postfix restart

Test whether Postfix is listening on port 465:

telnet localhost 465
Trying 127.0.0.1...                                                                           
Connected to localhost.                                                                       
Escape character is '^]'.
220 samhobbs.co.uk ESMTP Postfix (Debian/GNU)
ehlo samhobbs.co.uk
250-samhobbs
250-PIPELINING
250-SIZE 10240000
250-VRFY
250-ETRN
250-STARTTLS
250-AUTH PLAIN LOGIN
250-ENHANCEDSTATUSCODES
250-8BITMIME
250 DSN
quit
221 2.0.0 Bye
Connection closed by foreign host.

OK, so now it’s listening on the right port, but it’s allowing unencrypted connections. Here’s how you force TLS on port 465: open /etc/postfix/master.cf and find the line you uncommented earlier. Below it are some options, you want to edit them so that they look like this (i.e. uncomment lines 2 and 3):

smtps     inet  n       -       -       -       -       smtpd
  -o syslog_name=postfix/smtps
  -o smtpd_tls_wrappermode=yes

Line 3 is forcing TLS on port 465, and line 2 means that connections to port 465 have a different label in the logs, which can be useful for debugging.

sudo service postfix restart

Now try connecting with Telnet again… you should be able to establish a connection, but not receive any prompts from the server:

telnet localhost 465                                            
Trying 127.0.0.1...                                                                           
Connected to localhost.
Escape character is '^]'.
exit
exit
Connection closed by foreign host.

Now try openssl:

openssl s_client -connect localhost:465 -quiet
depth=0 CN = samhobbs
verify error:num=18:self signed certificate
verify return:1
depth=0 CN = samhobbs
verify return:1
220 samhobbs.co.uk ESMTP Postfix (Debian/GNU)
quit
221 2.0.0 Bye

Good: we are able to start a TLS encrypted connection. We got some errors because the certificate is self-signed (it's not signed by a certificate that is in the trusted root store on the server) but this is OK because we're just using the certificate for testing for now. When you come back later to set up a proper certificate, you can use this command to verify it. The -CApath option tells openssl where the trusted certificates are stored on your system:

openssl s_client -connect localhost:465 -quiet -CApath /etc/ssl/certs

Successful validation looks something like this:

sam@samhobbs:~$ openssl s_client -connect localhost:465 -quiet -CApath /etc/ssl/certs
depth=3 C = SE, O = AddTrust AB, OU = AddTrust External TTP Network, CN = AddTrust External CA Root
verify return:1                                                                              
depth=2 C = GB, ST = Greater Manchester, L = Salford, O = COMODO CA Limited, CN = COMODO RSA Certification Authority
verify return:1                                                                              
depth=1 C = GB, ST = Greater Manchester, L = Salford, O = COMODO CA Limited, CN = COMODO RSA Domain Validation Secure Server CA
verify return:1                                                                              
depth=0 OU = Domain Control Validated, OU = PositiveSSL, CN = samhobbs.co.uk                 
verify return:1                                                                              
220 samhobbs.co.uk ESMTP Postfix (Ubuntu)                                                    
quit                                                                                         
221 2.0.0 Bye

There are a couple more changes we want to make here: first, tell Postfix to only advertise SASL authentication over encrypted connections (so that you don’t accidentally send your password in the clear). Open /etc/postfix/main.cf and add this line:

smtpd_tls_auth_only = yes
sudo service postfix reload

Now connect to port 25 and you shouldn’t see AUTH advertised:

telnet localhost 25
Trying 127.0.0.1...
Connected to localhost.
Escape character is '^]'.
220 samhobbs.co.uk ESMTP Postfix (Debian/GNU)
ehlo samhobbs.co.uk
250-samhobbs.co.uk
250-PIPELINING
250-SIZE 10240000
250-VRFY
250-ETRN
250-STARTTLS
250-ENHANCEDSTATUSCODES
250-8BITMIME
250 DSN

Lastly, we want to override the smtp_recipient_restrictions for port 465 so that it doesn't accept incoming messages from unauthenticated users. At first, I didn't make this change and I noticed that some spam emails were coming in on port 465 and bypassing my spam filter, which I configured to scan all incoming email on port 25, but not 465 because I only expected it to be used for outgoing email. We can do this by overriding the smtp_recipient_restrictions list for port 465 in /etc/postfix/master.cf. Open master.cf and find the smtps line. Add a new recipient restrictions list option like this:

smtps     inet  n       -       -       -       -       smtpd
  -o syslog_name=postfix/smtps
  -o smtpd_tls_wrappermode=yes
  -o smtpd_recipient_restrictions=permit_sasl_authenticated,reject

Now reload postfix:

sudo service postfix reload

Perfect! Postfix configuration is now complete.

Testing IMAP

There are two main protocols for fetching mail: POP and IMAP. The main difference between them is what they do with emails when they collect them: a POP client will fetch email from your server and remove it from the server when it’s done. This is inconvenient if you want to connect with two or more devices (like a phone and a computer) and have complete copies of all your emails on both. IMAP, on the other hand, makes a copy of the emails on the server and leaves the originals there. For this reason, I think IMAP is much more useful than POP and I didn’t even bother to set up POP on my server. We can now test the IMAP server with Telnet in a similar way to SMTP & SASL testing earlier. This time, we’ll be using port 143, the standard port for IMAP. The stages are:

  1. establish a connection with telnet localhost 143
  2. log in with a login "USERNAME" "PASSWORD"" (not base64 encoded this time)
  3. select inbox to see messages inside b select inbox
  4. logout with c logout

In case you're wondering, the "a b c" thing is done because a client can send multiple commands to the server at once, and they might not come back in the same order depending on what they are. So, the responses have the same letter as the commands they are responding to so that the client doesn't get muddled. Here’s an example, using the testmail user we created earlier:

telnet localhost 143
Trying 127.0.0.1...
Connected to localhost.
Escape character is '^]'.
* OK [CAPABILITY IMAP4rev1 LITERAL+ SASL-IR LOGIN-REFERRALS ID ENABLE IDLE STARTTLS AUTH=PLAIN AUTH=LOGIN] Dovecot ready.
a login "testmail" "test1234"
a OK [CAPABILITY IMAP4rev1 LITERAL+ SASL-IR LOGIN-REFERRALS ID ENABLE IDLE SORT SORT=DISPLAY THREAD=REFERENCES THREAD=REFS MULTIAPPEND UNSELECT CHILDREN NAMESPACE UIDPLUS LIST-EXTENDED I18NLEVEL=1 CONDSTORE QRESYNC ESEARCH ESORT SEARCHRES WITHIN CONTEXT=SEARCH LIST-STATUS SPECIAL-USE] Logged in
b select inbox
* FLAGS (\Answered \Flagged \Deleted \Seen \Draft)
* OK [PERMANENTFLAGS (\Answered \Flagged \Deleted \Seen \Draft \*)] Flags permitted.
* 1 EXISTS
* 0 RECENT
* OK [UNSEEN 1] First unseen.
* OK [UIDVALIDITY 1385217480] UIDs valid
* OK [UIDNEXT 2] Predicted next UID
* OK [NOMODSEQ] No permanent modsequences
b OK [READ-WRITE] Select completed.
c logout
* BYE Logging out
c OK Logout completed.
Connection closed by foreign host.

Adding TLS support

Now that we know IMAP is working, we need to enable IMAPS (imap with SSL/TLS). The standard port for this is 993. Many other tutorials that were written for older versions of dovecot will tell you to do this in different ways that won’t work, I tried 3 different methods before I ended up with a working one. First, edit /etc/dovecot/conf.d/10-master.conf, find the “service imap-login” block and uncomment the port and SSL lines so that it looks like this:

service imap-login {
  inet_listener imap {
    port = 143
  } 
  inet_listener imaps {
    port = 993
    ssl = yes
  }
}

Edit 14/10/2015: the default dovecot configuration files changed recently after Jessie became the new stable distribution of Debian, which caused some users problems; TLS on port 993 used to be enabled by default but now it isn't. We need to re-enable it. In /etc/dovecot/conf.d/10-ssl.conf, find ssl = no and change it to:

ssl = yes

There have been some security vulnerabilities discovered in older versions of the SSL protocol in recent times. SSLv2 is disabled by default, but it doesn't harm to explicitly disable it again. SSLv3 is vulnerable to an attack called POODLE, so we will disable it too. In the same file, find the ssl_protocols parameter line, uncomment it and add !SSLv3 to the end, like this:

ssl_protocols = !SSLv2 !SSLv3

Edit 02/09/2017: if you're using Debian Stretch or later, or one of its derivatives, then you will need to edit that line to match the following. The SSLv2 option is no longer recognised as an option for ssl_protocols because it has been removed entirely:

ssl_protocols = !SSLv3

For some bizarre reason, the Dovecot package for Raspberry Pi (and possibly newer versions of Ubuntu) does not create a self-signed certificate during installation like it used to. So, we have to create one manually. If you look in /usr/share/dovecot/ you will find the script that used to be used to generate the certificate; we can use it ourselves to simplify the process. The script is located at /usr/share/dovecot/mkcert.sh and looks like this:

#!/bin/sh

# Generates a self-signed certificate.
# Edit dovecot-openssl.cnf before running this.

OPENSSL=${OPENSSL-openssl}
SSLDIR=${SSLDIR-/etc/ssl}
OPENSSLCONFIG=${OPENSSLCONFIG-dovecot-openssl.cnf}

CERTDIR=/etc/dovecot
KEYDIR=/etc/dovecot/private

CERTFILE=$CERTDIR/dovecot.pem
KEYFILE=$KEYDIR/dovecot.pem

if [ ! -d $CERTDIR ]; then
  echo "$SSLDIR/certs directory doesn't exist"
  exit 1
fi

if [ ! -d $KEYDIR ]; then
  echo "$SSLDIR/private directory doesn't exist"
  exit 1
fi

if [ -f $CERTFILE ]; then
  echo "$CERTFILE already exists, won't overwrite"
  exit 1
fi

if [ -f $KEYFILE ]; then
  echo "$KEYFILE already exists, won't overwrite"
  exit 1
fi

$OPENSSL req -new -x509 -nodes -config $OPENSSLCONFIG -out $CERTFILE -keyout $KEYFILE -days 365 || exit 2
chmod 0600 $KEYFILE
echo 
$OPENSSL x509 -subject -fingerprint -noout -in $CERTFILE || exit 2

If you were going to use this certificate for any significant length of time, it would be worth editing the parameters in the config file it uses (/usr/share/dovecot/dovecot-openssl.cnf) to set the proper common name and contact details on the certificate. However, I suggest you leave the defaults as they are, use this certificate just for testing, and then come back later and generate a new cert when everything is working (more on that later). You must be in the same folder as the configuration file when you run the script, or it will not find the config and the certificate generation will fail. The following two commands will change to the right folder and then execute the script:

cd /usr/share/dovecot
sudo ./mkcert.sh

You should see a message "writing new private key to '/etc/dovecot/private/dovecot.pem'" and then some details about the certificate. Next, find the following two lines in /etc/dovecot/conf.d/10-ssl.conf and uncomment them:

#ssl_cert = </etc/dovecot/dovecot.pem
#ssl_key = </etc/dovecot/private/dovecot.pem

Now reload dovecot to apply the changes:

sudo service dovecot reload

Since IMAPS is a connection over SSL/TLS, we can’t use Telnet to test it. Instead, we use openssl to create a secure connection. There are two versions of the command, one will show you LOADS of information about the certificate used to encrypt the connection, and the other will suppress this info. I recommend trying the long version out of interest, but both will work the same for the test: For full information:

openssl s_client -connect localhost:993

For minimal information:

openssl s_client -connect localhost:993 -quiet

I won’t print the output of the first command, because it’s ridiculously long. Here’s an example of the second, including a login test:

admin@samhobbs /etc/dovecot/conf.d $ openssl s_client -connect localhost:993 -quiet
depth=0 O = Dovecot mail server, OU = samhobbs, CN = samhobbs, emailAddress = root@samhobbs.co.uk
verify error:num=18:self signed certificate
verify return:1
depth=0 O = Dovecot mail server, OU = samhobbs, CN = samhobbs, emailAddress = root@samhobbs.co.uk
verify return:1
* OK [CAPABILITY IMAP4rev1 LITERAL+ SASL-IR LOGIN-REFERRALS ID ENABLE IDLE AUTH=PLAIN AUTH=LOGIN] Dovecot ready.
a login "testmail" "test1234"
a OK [CAPABILITY IMAP4rev1 LITERAL+ SASL-IR LOGIN-REFERRALS ID ENABLE IDLE SORT SORT=DISPLAY THREAD=REFERENCES THREAD=REFS MULTIAPPEND UNSELECT CHILDREN NAMESPACE UIDPLUS LIST-EXTENDED I18NLEVEL=1 CONDSTORE QRESYNC ESEARCH ESORT SEARCHRES WITHIN CONTEXT=SEARCH LIST-STATUS SPECIAL-USE] Logged in
b logout
* BYE Logging out
b OK Logout completed.
Connection closed by foreign host.

Good stuff: SSL/TLS is working on port 993, and you can log in successfully. Note that by default Dovecot uses a “snakeoil” self-signed certificate. SSL/TLS certificates are used for two purposes: encryption and verification. The “snakeoil” certificate will encrypt your content but it won’t verify that you’re talking to your server – you could be talking to someone imitating your server (anyone can create a self-signed certificate claiming to be any website). If you’d like to get your certificate signed without forking out loads of money to a cert signing authority, I’d recommend CAcert. I've written a tutorial explaining how to generate your own cert and get it signed here. If you opt for a commercial certificate, you can use the CAcert tutorial to generate the certificate and then this tutorial will explain the differences in the installation/configuration of commercial certificates once you have it signed. If you're testing a proper certificate, use this command to tell openssl where the trusted root certificates are stored:

openssl s_client -connect localhost:993 -quiet -CApath /etc/ssl/certs

Tidying up and enabling WAN access

Before opening the ports on your router to the world, it’s a good idea to delete that test user because the password is so easy to guess.

sudo userdel testmail

Also, if you still use the "pi" login, for goodness' sake change the password from "raspberry"! You can do this using the passwd command when logged in as pi:

passwd

Or you can achieve the same thing when logged in as another user by using sudo to gain root privileges:

sudo passwd pi

Now you can open a few ports on your router’s firewall. Make sure your Pi has a static LAN IP address and then forward these ports from WAN to its LAN IP address:

  • Port 25 for SMTP (used for receiving emails)
  • Port 465 for secure SMTP (used for sending emails after SASL authentication)
  • Port 993 for IMAPS (used to receive emails on your phone/tablet/computer)

Here’s an example on my router, running OpenWrt: openwrt-port-forwards-raspberry-pi-email-server.png

Setting up IMAP Email Clients

I’m now going to run through setting up IMAP email clients quickly, using K9 Mail on Android and Thunderbird on GNU/Linux as examples. The setup for Thunderbird on Windows and Mac OSX should be very similar. The basics are this:

  • Select an IMAP connection
  • Your login is your username only (omit @yourdomain.com), and you password is…your password!
  • For incoming emails: select use SSL/TLS always and the program should automatically select port 993
  • For outgoing emails: select SSL/TLS always. The program may suggest port 587, but you want port 465

K9 Mail

Open K9 Mail and select add new account. Type in your account information (you@yourdomain.com and password) and then select manual setup. Select IMAP and then enter your information as follows… Incoming email: K9 Incoming Email Settings Outgoing email: K9 Outgoing Email Settings

Thunderbird

Open Thunderbird, and then click Account Actions –> Add Mail Account. Fill in your password and email address, which is your username followed by your fully qualified domain name (FQDN), i.e. username@yourdomain.com: Thunderbird Step 1: Mail Account Setup Thunderbird will try to auto-detect settings and fail. Don’t worry, this is normal. Select “manual config”:  Thunderbird Step 2: TB will try to autodetect settings, and fail. Select “Manual Config" Now edit the settings as appropriate. I had to remove a period (.) from in front of my “server hostname”, and edit the SSL and Authentication settings. If you select “SSL/TLS” for both incoming and outgoing, ports 993 and 465 are automatically selected: Thunderbird Step 3: Edit the settings so that they match these (but change them to match your username and domain name!) Now try emailing yourself from your external email address, and see if your email gets through. If you are having problems, be sure to check you’ve set up an MX record as well as a DNS A record.

Stuck in spam filters?

A few people have contacted me recently to say that their email server is working fine but their emails are getting sent to Gmail's spam folder. If you are experiencing problems like this (or even if you're not), try setting up an SPF and/or PTR record as explained in my DNS basics tutorial. You might also want to check if your domain name or IP address are on any blacklists. There's a handy website called MX toolbox that lets you do this (choose blacklist check from the dropdown menu).

Almost done…

Good news! If you’ve reached this far and everything is working, then you’re almost done. The next step (Webmail with Squirrelmail) is optional but by far the easiest of the three steps. If you’ve hit a rut, please post a comment and I’ll try and help you out. If not… continue to Raspberry Pi Email Server Part 3: Squirrelmail

Comments

Maybe your ISP is blocking port 25, can you telnet to samhobbs.co.uk on port 25?
telnet samhobbs.co.uk 25
What kind of network are you on? I've not had that "no servers could be reached" error before, wondering if a firewall is blocking your dns request. Sam

/etc/dovecot/dovecot.pem already exists, won't overwrite

They probably fixed the packaging error and started distributing Dovecot with a snakeoil cert again. Ignore it and move on :)

I follow the tutorial it is ok but i can't send email. Here is the response:
host gmail-smtp-in.l.google.com[66.102.1.27] said:
550-5.1.1 The email account that you tried to reach does not exist. Please
try 550-5.1.1 double-checking the recipient's email address for typos or
550-5.1.1 unnecessary spaces. Learn more at 550 5.1.1
https://support.google.com/mail/answer/6596 67si4485679wmd.46 - gsmtp (in
reply to RCPT TO command)

Please help
Thank you.

Yash Ballani

Fri, 07/01/2016 - 10:11

I am able to sign in to my user via IMAPS and SMTPS but when I am trying to send a email from that account or receive a email on that account, mail bounces back :/ I have followed both part 1 and part 2 of your tutorial

I have it all set up, and have access to it via my phone, but I cannot send messages out as user 'pi', or recieve. Please can you help? If you need to test it, I can email you the login details to a secondary user I have.

Hi Sam

Thanks for this fantastic Tutorial.

I have a Problem on the IMAP Test. I can login, but when I type "b select Inbox" I only get an answer like: b NO [SERVERBUG] Internal error occurred.
I hope you can help me.

Greetings Luca

Hi Luca, You probably missed the "tell dovecot where your mailbox is" step, or the parameter is in your config file twice and is being overridden (dovecot is looking in /var/mail). Sam

Cameron Trow

Tue, 08/23/2016 - 22:06

pi@tumblenet ~ $ sudo service dovecot restart
Job for dovecot.service failed. See 'systemctl status dovecot.service' and 'journalctl -xn' for details.
pi@tumblenet ~ $ systemctl status dovecot.service
● dovecot.service - LSB: Dovecot init script
Loaded: loaded (/etc/init.d/dovecot)
Active: failed (Result: exit-code) since Tue 2016-08-23 21:01:14 UTC; 17s ago
Process: 26980 ExecStop=/etc/init.d/dovecot stop (code=exited, status=0/SUCCESS)
Process: 27135 ExecStart=/etc/init.d/dovecot start (code=exited, status=1/FAILURE)
pi@tumblenet ~ $ journalctl -xn
No journal files were found.

Hi Sam thank you for your very informative tutorial.
i have managed to get a static ip (for free from my isp directsavetelecom). but cant get am MX record with "free" sub-domain from DYNDNS.ORG (or i have not found out how to, as i have yet to contact their help desk.
I am very new to this and have re imaged and started again 3 times because i don't yet know how to back track.
i have a working email server almost. i can sent and receive from some email addresses
i have tried to receive from a standard yahoo email account and my pi is rejecting it, mail log
buck postfix/smtpd[7743]: NOQUEUE: reject: RCPT from unknown[212.82.96.218]: 450 4.7.1 <nm17-vm3.bullet.mail.ir2.yahoo.com>: Helo command rejected: Host not found; from=<akabuck2001@yahoo.co.uk> to=<root@buck.broke-it.net> proto=ESMTP helo=<nm17-vm3.bullet.mail.ir2.yahoo.com>
buck postfix/smtpd[7790]: NOQUEUE: reject: RCPT from unknown[212.82.96.218]: 450 4.7.1 <nm17-vm3.bullet.mail.ir2.yahoo.com>: Helo command rejected: Host not found; from=<akabuck2001@yahoo.co.uk> to=<root@buck.broke-it.net> proto=ESMTP helo=<nm17-vm3.bullet.mail.ir2.yahoo.com>
if i comment out the line "reject_invalid_helo_hostname"
it comes through
smtpd_relay_restrictions = permit_mynetworks permit_sasl_authenticated defer_unauth_destination
smtpd_recipient_restrictions =
permit_sasl_authenticated,
permit_mynetworks,
reject_unauth_destination
smtpd_helo_required = yes
smtpd_helo_restrictions =
permit_mynetworks,
permit_sasl_authenticated,
# reject_invalid_helo_hostname,
reject_non_fqdn_helo_hostname,
reject_unknown_helo_hostname,
check_helo_access hash:/etc/postfix/helo_access
buck postfix/local[8054]: E395D41385: to=<pi@buck.broke-it.net>, orig_to=<root@buck.broke-it.net>, relay=local, delay=0.27, delays=0.23/0.03/0/0.02, dsn=2.0.0, status=sent (delivered to maildir)

not sure why it is failing the check
any help please
regards
Andrew

sent as plain text as previous removed some data

Hi, It shouldn't be failing, because that's a real hostname with a DNS A record - check if you can retrieve it using dig:
dig nm17-vm3.bullet.mail.ir2.yahoo.com
You should only get that message when the client helo's with a hostname that doesn't have a DNS A or MX record. Sam

dig gets a good reply
andrew.ryan@buck:~ $ dig nm17-vm3.bullet.mail.ir2.yahoo.com

; <<>> DiG 9.9.5-9+deb8u6-Raspbian <<>> nm17-vm3.bullet.mail.ir2.yahoo.com
;; global options: +cmd
;; Got answer:
;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 15873
;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 5, ADDITIONAL: 1

;; OPT PSEUDOSECTION:
; EDNS: version: 0, flags:; udp: 4096
;; QUESTION SECTION:
;nm17-vm3.bullet.mail.ir2.yahoo.com. IN A

;; ANSWER SECTION:
nm17-vm3.bullet.mail.ir2.yahoo.com. 1800 IN A 212.82.96.218

;; AUTHORITY SECTION:
ir2.yahoo.com. 172800 IN NS ns1.yahoo.com.
ir2.yahoo.com. 172800 IN NS ns3.yahoo.com.
ir2.yahoo.com. 172800 IN NS ns4.yahoo.com.
ir2.yahoo.com. 172800 IN NS ns2.yahoo.com.
ir2.yahoo.com. 172800 IN NS ns5.yahoo.com.

;; Query time: 39 msec
;; SERVER: 192.168.1.1#53(192.168.1.1)
;; WHEN: Wed Aug 24 16:31:02 BST 2016
;; MSG SIZE rcvd: 169

removed the line comment.
did a postfix reload and a postfix service restart as not sure what one i should use
sent another mail from my phone yahoo account and it worked
Aug 24 16:40:08 buck postfix/smtpd[12832]: connect from nm30.bullet.mail.ir2.yahoo.com[212.82.96.55]
Aug 24 16:40:09 buck postfix/smtpd[12832]: 36B9C40381: client=nm30.bullet.mail.ir2.yahoo.com[212.82.96.55]
Aug 24 16:40:09 buck postfix/cleanup[12838]: 36B9C40381: message-id=<1941667547.156302.1472053207601.JavaMail.yahoo@mail.yahoo.com>
Aug 24 16:40:09 buck postfix/qmgr[12716]: 36B9C40381: from=<akabuck2001@yahoo.co.uk>, size=2341, nrcpt=1 (queue active)
Aug 24 16:40:10 buck postfix/smtpd[12832]: disconnect from nm30.bullet.mail.ir2.yahoo.com[212.82.96.55]
Aug 24 16:40:10 buck postfix/local[12839]: 36B9C40381: to=<andrew.ryan@buck.broke-it.net>, relay=local, delay=1.1, delays=0.62/0.01/0/0.41, dsn=2.0.0, status=sent (delivered to maildir)

still don't know why.
i will now carry on with the rest of your tutorial and install the spam filter
thanks again for you very good instructions
and your reply

regards
Andrew

Hi Sam. I followed parts 1 & 2 -- everything seemed to go fine -- but I can neither send nor receive email. Ports 465 and 993 are open, and my ISP blocks port 25. I tried some work arounds without success. (I used http://canyouseeme.org to check ports.)

If port 465 is open and the TLS related steps in your tutorial have been implemented, why is port 25 required? Shouldn't the "normal" port 25 activity just flow elsewhere?

Thanks for all your help and effort!

Hi Michael, Unfortunately, server to server connections are always made on port 25 and never never port 465, we're only using that for client to server connections. If S2S connections were made on port 465 as well as port 25, ISPs would block that port too! Can you get a static IP address from your ISP? Sometimes they block ports on the dynamic ranges but not the static IPs. Sam

I believe I followed the great tutorial through Postfix and Dovecot. I have not installed Squirrelmail yet, but I have used it in the past.

I think I am close, but I am not receiving email. The mail.log looks like other servers are not connecting. Can you tell me what to test or otherwise think you know what's wrong? Again, I believe that at each step you said to test, it worked flawlessly, but apparently some config is out of order. Thanks! There are some SSL Accept errors, but there are other disconnects without this error. Nothing is received in my mailbox. Here is the tail of the mail.log:

pi@raspberrypi ~ $ sudo tail -f /var/log/mail.log
Aug 25 17:44:44 raspberrypi postfix/smtps/smtpd[1518]: connect from sdcmeg1.ecommunity.com[198.140.195.27]
Aug 25 17:45:04 raspberrypi postfix/smtps/smtpd[1381]: SSL_accept error from sdcmeg1.ecommunity.com[198.140.195.27]: lost connection
Aug 25 17:45:04 raspberrypi postfix/smtps/smtpd[1518]: SSL_accept error from sdcmeg1.ecommunity.com[198.140.195.27]: lost connection
Aug 25 17:45:04 raspberrypi postfix/smtps/smtpd[1381]: lost connection after CONNECT from sdcmeg1.ecommunity.com[198.140.195.27]
Aug 25 17:45:04 raspberrypi postfix/smtps/smtpd[1518]: lost connection after CONNECT from sdcmeg1.ecommunity.com[198.140.195.27]
Aug 25 17:45:04 raspberrypi postfix/smtps/smtpd[1381]: disconnect from sdcmeg1.ecommunity.com[198.140.195.27]
Aug 25 17:45:04 raspberrypi postfix/smtps/smtpd[1518]: disconnect from sdcmeg1.ecommunity.com[198.140.195.27]
Aug 25 17:45:12 raspberrypi postfix/smtps/smtpd[1381]: connect from mtaout-207-ewr.sendlabs.com[216.146.33.207]
Aug 25 17:45:12 raspberrypi postfix/smtps/smtpd[1518]: connect from mail11.smartbrief.com[72.32.59.11]
Aug 25 17:45:45 raspberrypi postfix/smtps/smtpd[1520]: connect from cbdl3626.caringbridge.org[66.162.232.156]
Aug 25 17:46:13 raspberrypi postfix/smtps/smtpd[1380]: SSL_accept error from mail136.mmsend.com[64.27.72.136]: Connection reset by peer
Aug 25 17:46:13 raspberrypi postfix/smtps/smtpd[1380]: lost connection after CONNECT from mail136.mmsend.com[64.27.72.136]
Aug 25 17:46:13 raspberrypi postfix/smtps/smtpd[1380]: disconnect from mail136.mmsend.com[64.27.72.136]
Aug 25 17:46:13 raspberrypi postfix/smtps/smtpd[1380]: connect from mail136.mmsend.com[64.27.72.136]
Aug 25 17:46:15 raspberrypi dovecot: imap-login: Disconnected (no auth attempts in 2 secs): user=<>, rip=169.54.233.126, lip=192.168.2.3, TLS handshaking: Disconnected, session=
Aug 25 17:46:35 raspberrypi postfix/smtps/smtpd[1542]: connect from mail147.atl121.mcsv.net[198.2.131.147]
Aug 25 17:47:16 raspberrypi postfix/smtps/smtpd[1543]: connect from mta.email-carmax.com[66.231.85.121]
Aug 25 17:47:18 raspberrypi postfix/smtps/smtpd[1544]: connect from sdcmeg1.ecommunity.com[198.140.195.27]
Aug 25 17:47:38 raspberrypi postfix/smtps/smtpd[1544]: SSL_accept error from sdcmeg1.ecommunity.com[198.140.195.27]: lost connection
Aug 25 17:47:38 raspberrypi postfix/smtps/smtpd[1544]: lost connection after CONNECT from sdcmeg1.ecommunity.com[198.140.195.27]
Aug 25 17:47:38 raspberrypi postfix/smtps/smtpd[1544]: disconnect from sdcmeg1.ecommunity.com[198.140.195.27]

No, it's not a port scan thing - I can't receive ANY email. I have installed Squirrelmail now, and when I login using Squirrelmail, I see the appropriate entries in mail.log. But I can't receive from ANY outside emailer. Do you have time to look at my main.cf and master.cf if I post? I feel certain that something's wrong with the Postfix config. A few years ago I had a Postfix-Courier server going with Squirrelmail, but I am struggling with getting this one up correctly. Thanks!

I find it's rarely helpful to post whole config files. Can you send mail? If not, it could be a total port block (incoming and outgoing). If you are able to send mail it might be a DNS problem, your own firewall (port forwards), or some other config error. If so, please post your domain name and current IP and I'll check your DNS. Sam

Add new comment

The content of this field is kept private and will not be shown publicly.

Filtered HTML

  • Web page addresses and email addresses turn into links automatically.
  • Allowed HTML tags: <a href hreflang> <em> <strong> <cite> <blockquote cite> <code> <ul type> <ol start type> <li> <dl> <dt> <dd>
  • Lines and paragraphs break automatically.