Raspberry Pi Email Server Part 2: Dovecot

Powered by Drupal
Submitted by Sam Hobbs on

Dovecot Logo This is the second part of a five part tutorial that will show you how to install a full featured email server on your Raspberry Pi. This tutorial covers Dovecot, which provides SASL authentication and IMAP capabilities.

The parts are:

The Introduction & Contents Page (read first)

Raspberry Pi Email Server Part 1: Postfix

Raspberry Pi Email Server Part 2: Dovecot

Raspberry Pi Email Server Part 3: Squirrelmail

Raspberry Pi Email Server Part 4: Spam Detection with Spamassassin

Raspberry Pi Email Server Part 5: Spam Sorting with LMTP & Sieve

Fixing the errors that appeared during dovecot installation

In part 1, when you installed Dovecot I mentioned that you might see some errors like this:

Creating config file /etc/dovecot/conf.d/20-imap.conf with new version
[....] Restarting IMAP/POP3 mail server: dovecotError: socket() failed: Address family not supported by protocol
Error: service(imap-login): listen(::, 143) failed: Address family not supported by protocol
Error: socket() failed: Address family not supported by protocol
Error: service(imap-login): listen(::, 993) failed: Address family not supported by protocol
Fatal: Failed to start listeners
 failed!
invoke-rc.d: initscript dovecot, action "restart" failed.
dpkg: error processing dovecot-imapd (--configure):
 subprocess installed post-installation script returned error exit status 1
Setting up dovecot-ldap (1:2.1.7-7) ...

These errors are caused by the lack of IPv6 support, which I mentioned in the previous tutorial. To remove the errors, open the main dovecot configuration file (/etc/dovecot/dovecot.conf) and find this line:

listen = *, ::

And change it to:

listen = *

The * means “all IPv4 addresses”, the :: means “all IPv6 addresses”. Now restart Dovecot, and you shouldn’t get any errors:

sudo service dovecot restart

Note: since I wrote this tutorial, there have been a few small changes to the default configuration file - you may find that the line is commented (with a # at the start of the line). If so, remember to uncomment it when you make your changes!

Tell Dovecot where your Mailbox is

Open /etc/dovecot/conf.d/10-mail.conf and find this line:

mail_location = mbox:~/mail:INBOX=/var/mail/%u

Change it to this:

mail_location = maildir:~/Maildir

Instruct Postfix to use Dovecot SASL

Now we need to tell Postfix that we would like to use Dovecot for SASL authentication. Open /etc/postfix/main.cf and add these lines:

smtpd_sasl_type = dovecot
smtpd_sasl_path = private/auth
smtpd_sasl_auth_enable = yes

Now tell Dovecot to listen for SASL authentication requests from Postfix. Open /etc/dovecot/conf.d/10-master.conf and comment out the current block that begins with service auth (place a # at the start of each line). Replace it with this:

service auth {
        unix_listener /var/spool/postfix/private/auth {
                mode = 0660
                user = postfix
                group = postfix
        }
}

Now you want to enable plain text logins. Do it by adding these two lines to /etc/dovecot/conf.d/10-auth.conf. Make sure they are not already present in the file, or your settings may be overwritten with the default ones if the default is declared later in the file than the lines you add. If the parameters are already present, you can either modify the existing lines or comment them out and add these new ones:

disable_plaintext_auth = no
auth_mechanisms = plain login

Note that although the logins are in plain text, we will be setting Postfix up later so that it only allows you to use plaintext logins from within SSL/TLS. This means that your login and password will sent in an encrypted session - you wouldn't see them in plain text if you used a packet sniffer, for example. For now, we’re allowing unencrypted plain text logins so that we can test logging in with Telnet. Since the connection is local (from the Pi to the Pi), your password isn’t being sent over any insecure networks so this is fine.

Testing SASL

Creating a new user for testing purposes is a good idea. Let’s call this temporary user testmail and give it the password test1234 Use this command to add the user, and follow the prompts including setting a password.

sudo adduser testmail

Now restart Postfix and Dovecot:

sudo service postfix restart
sudo service dovecot restart

We’re now going to try and send an email after authenticating with SASL. The server is expecting to see a base64 encoded version of your username and password, so we have to convert it first. There are three ways of doing this, so I've given examples below using the testmail username and test1234 password:

#Method No.1
echo -ne '\000testmail\000test1234' | openssl base64

#Method No.2
perl -MMIME::Base64 -e 'print encode_base64("\0testmail\0test1234");'

#Method No.3
printf '\0%s\0%s' 'testmail' 'test1234' | openssl base64

I have discovered that if your password starts with a number, methods 1 and 2 don’t work. Assuming the username and password are testmail and test1234, the commands produce this:

AHRlc3RtYWlsAHRlc3QxMjM0

WARNING: If you’re having problems with authentication and you paste examples to forums or mailing lists, be aware that it is really easy to convert this back into your username and password (hence the creation of a test user). If you're using your real username and password to test, redact it before posting! Now, still logged into the Pi via SSH, you can telnet port 25 to test whether or not SASL is working. There’s only one extra step, which is the AUTH PLAIN command that comes after ehlo but before mail from. For testing, the permit_mynetworks parameter should be commented out under your postfix smtpd_recipient_restrictions block in /etc/postfix/main.cf. If you’re following on from Raspberry Pi Email Server Part 1: Postfix then this should already be the case. If you have to change it, remember to reload postfix (sudo service postfix reload) after you change the value. Here’s an example:

telnet localhost 25
Trying 127.0.0.1...
Connected to localhost.
Escape character is '^]'.
220 samhobbs ESMTP Postfix (Debian/GNU)
ehlo facebook.com
250-samhobbs
250-PIPELINING
250-SIZE 10240000
250-VRFY
250-ETRN
250-STARTTLS
250-AUTH PLAIN LOGIN
250-ENHANCEDSTATUSCODES
250-8BITMIME
250 DSN
AUTH PLAIN AHRlc3RtYWlsAHRlc3QxMjM0
235 2.7.0 Authentication successful
mail from:testmail
250 2.1.0 Ok
rcpt to:me@externalemail.com
250 2.1.5 Ok
data
354 End data with .
Subject: This is my first email that has been authenticated with Dovecot SASL
Woop woop
.
250 2.0.0 Ok: queued as B87133F768
quit
221 2.0.0 Bye
Connection closed by foreign host.

Now try again but enter the username/password incorrectly (base64 encode something random) – you should get an error message and the email won’t send. If everything went to plan, then SASL is working properly! You can now uncomment permit_mynetworks again.

Separating Incoming email (unauthenticated) from Outgoing Email (SASL authenticated)

It’s probably a good idea to have a dedicated port for sending outgoing email…here’s why: Port 25 doesn’t require (but does offer) SSL/TLS encryption. If you mess up configuring your mail client you could end up letting it authenticate with SASL over insecure connections. Using a different port that only accepts SSL/TLS connections removes the risk that a poorly configured email client could be sending your password unencrypted over dodgy networks. There are two ports you can use for this:

  1. 465: SMTP over SSL
  2. 587: Email submission

587 is the “official” port for email clients (like K9 mail, Thunderbird and Outlook) to use when submitting messages to the Mail Submission Agent (your email server) – the submission may be encrypted or unencrypted depending on the server configuration. 465 was a port that was assigned for SMTP with SSL/TLS before the STARTTLS protocol was introduced, back in the days when you chose your port and that decided on the type of connection you were going to get (encrypted or unencrypted). STARTTLS changed things because it allows you to connect with an unencrypted connection (like the one you get with Telnet), and then upgrade to an encrypted connection without changing port… so when STARTTLS was introduced, SMTPS on port 465 was removed from the standard because you could do the same thing with a single port (25). However, I think there is some value in specifying a port for submission that only accepts SSL/TLS encrypted connections, and won’t work if the connection isn’t encrypted. This means that if you misconfigure your email client it just won’t work, instead of working and sending your password in an unencrypted format. So, anyway… Here’s how to set up Postfix to listen on port 465 for encrypted connections. The first step is telling Postfix to listen on port 465, so open /etc/postfix/master.cf and uncomment the line:

smtps     inet  n       -       -       -       -       smtpd

Now restart Postfix:

sudo service postfix restart

Test whether Postfix is listening on port 465:

telnet localhost 465
Trying 127.0.0.1...                                                                           
Connected to localhost.                                                                       
Escape character is '^]'.
220 samhobbs.co.uk ESMTP Postfix (Debian/GNU)
ehlo samhobbs.co.uk
250-samhobbs
250-PIPELINING
250-SIZE 10240000
250-VRFY
250-ETRN
250-STARTTLS
250-AUTH PLAIN LOGIN
250-ENHANCEDSTATUSCODES
250-8BITMIME
250 DSN
quit
221 2.0.0 Bye
Connection closed by foreign host.

OK, so now it’s listening on the right port, but it’s allowing unencrypted connections. Here’s how you force TLS on port 465: open /etc/postfix/master.cf and find the line you uncommented earlier. Below it are some options, you want to edit them so that they look like this (i.e. uncomment lines 2 and 3):

smtps     inet  n       -       -       -       -       smtpd
  -o syslog_name=postfix/smtps
  -o smtpd_tls_wrappermode=yes

Line 3 is forcing TLS on port 465, and line 2 means that connections to port 465 have a different label in the logs, which can be useful for debugging.

sudo service postfix restart

Now try connecting with Telnet again… you should be able to establish a connection, but not receive any prompts from the server:

telnet localhost 465                                            
Trying 127.0.0.1...                                                                           
Connected to localhost.
Escape character is '^]'.
exit
exit
Connection closed by foreign host.

Now try openssl:

openssl s_client -connect localhost:465 -quiet
depth=0 CN = samhobbs
verify error:num=18:self signed certificate
verify return:1
depth=0 CN = samhobbs
verify return:1
220 samhobbs.co.uk ESMTP Postfix (Debian/GNU)
quit
221 2.0.0 Bye

Good: we are able to start a TLS encrypted connection. We got some errors because the certificate is self-signed (it's not signed by a certificate that is in the trusted root store on the server) but this is OK because we're just using the certificate for testing for now. When you come back later to set up a proper certificate, you can use this command to verify it. The -CApath option tells openssl where the trusted certificates are stored on your system:

openssl s_client -connect localhost:465 -quiet -CApath /etc/ssl/certs

Successful validation looks something like this:

sam@samhobbs:~$ openssl s_client -connect localhost:465 -quiet -CApath /etc/ssl/certs
depth=3 C = SE, O = AddTrust AB, OU = AddTrust External TTP Network, CN = AddTrust External CA Root
verify return:1                                                                              
depth=2 C = GB, ST = Greater Manchester, L = Salford, O = COMODO CA Limited, CN = COMODO RSA Certification Authority
verify return:1                                                                              
depth=1 C = GB, ST = Greater Manchester, L = Salford, O = COMODO CA Limited, CN = COMODO RSA Domain Validation Secure Server CA
verify return:1                                                                              
depth=0 OU = Domain Control Validated, OU = PositiveSSL, CN = samhobbs.co.uk                 
verify return:1                                                                              
220 samhobbs.co.uk ESMTP Postfix (Ubuntu)                                                    
quit                                                                                         
221 2.0.0 Bye

There are a couple more changes we want to make here: first, tell Postfix to only advertise SASL authentication over encrypted connections (so that you don’t accidentally send your password in the clear). Open /etc/postfix/main.cf and add this line:

smtpd_tls_auth_only = yes
sudo service postfix reload

Now connect to port 25 and you shouldn’t see AUTH advertised:

telnet localhost 25
Trying 127.0.0.1...
Connected to localhost.
Escape character is '^]'.
220 samhobbs.co.uk ESMTP Postfix (Debian/GNU)
ehlo samhobbs.co.uk
250-samhobbs.co.uk
250-PIPELINING
250-SIZE 10240000
250-VRFY
250-ETRN
250-STARTTLS
250-ENHANCEDSTATUSCODES
250-8BITMIME
250 DSN

Lastly, we want to override the smtp_recipient_restrictions for port 465 so that it doesn't accept incoming messages from unauthenticated users. At first, I didn't make this change and I noticed that some spam emails were coming in on port 465 and bypassing my spam filter, which I configured to scan all incoming email on port 25, but not 465 because I only expected it to be used for outgoing email. We can do this by overriding the smtp_recipient_restrictions list for port 465 in /etc/postfix/master.cf. Open master.cf and find the smtps line. Add a new recipient restrictions list option like this:

smtps     inet  n       -       -       -       -       smtpd
  -o syslog_name=postfix/smtps
  -o smtpd_tls_wrappermode=yes
  -o smtpd_recipient_restrictions=permit_sasl_authenticated,reject

Now reload postfix:

sudo service postfix reload

Perfect! Postfix configuration is now complete.

Testing IMAP

There are two main protocols for fetching mail: POP and IMAP. The main difference between them is what they do with emails when they collect them: a POP client will fetch email from your server and remove it from the server when it’s done. This is inconvenient if you want to connect with two or more devices (like a phone and a computer) and have complete copies of all your emails on both. IMAP, on the other hand, makes a copy of the emails on the server and leaves the originals there. For this reason, I think IMAP is much more useful than POP and I didn’t even bother to set up POP on my server. We can now test the IMAP server with Telnet in a similar way to SMTP & SASL testing earlier. This time, we’ll be using port 143, the standard port for IMAP. The stages are:

  1. establish a connection with telnet localhost 143
  2. log in with a login "USERNAME" "PASSWORD"" (not base64 encoded this time)
  3. select inbox to see messages inside b select inbox
  4. logout with c logout

In case you're wondering, the "a b c" thing is done because a client can send multiple commands to the server at once, and they might not come back in the same order depending on what they are. So, the responses have the same letter as the commands they are responding to so that the client doesn't get muddled. Here’s an example, using the testmail user we created earlier:

telnet localhost 143
Trying 127.0.0.1...
Connected to localhost.
Escape character is '^]'.
* OK [CAPABILITY IMAP4rev1 LITERAL+ SASL-IR LOGIN-REFERRALS ID ENABLE IDLE STARTTLS AUTH=PLAIN AUTH=LOGIN] Dovecot ready.
a login "testmail" "test1234"
a OK [CAPABILITY IMAP4rev1 LITERAL+ SASL-IR LOGIN-REFERRALS ID ENABLE IDLE SORT SORT=DISPLAY THREAD=REFERENCES THREAD=REFS MULTIAPPEND UNSELECT CHILDREN NAMESPACE UIDPLUS LIST-EXTENDED I18NLEVEL=1 CONDSTORE QRESYNC ESEARCH ESORT SEARCHRES WITHIN CONTEXT=SEARCH LIST-STATUS SPECIAL-USE] Logged in
b select inbox
* FLAGS (\Answered \Flagged \Deleted \Seen \Draft)
* OK [PERMANENTFLAGS (\Answered \Flagged \Deleted \Seen \Draft \*)] Flags permitted.
* 1 EXISTS
* 0 RECENT
* OK [UNSEEN 1] First unseen.
* OK [UIDVALIDITY 1385217480] UIDs valid
* OK [UIDNEXT 2] Predicted next UID
* OK [NOMODSEQ] No permanent modsequences
b OK [READ-WRITE] Select completed.
c logout
* BYE Logging out
c OK Logout completed.
Connection closed by foreign host.

Adding TLS support

Now that we know IMAP is working, we need to enable IMAPS (imap with SSL/TLS). The standard port for this is 993. Many other tutorials that were written for older versions of dovecot will tell you to do this in different ways that won’t work, I tried 3 different methods before I ended up with a working one. First, edit /etc/dovecot/conf.d/10-master.conf, find the “service imap-login” block and uncomment the port and SSL lines so that it looks like this:

service imap-login {
  inet_listener imap {
    port = 143
  } 
  inet_listener imaps {
    port = 993
    ssl = yes
  }
}

Edit 14/10/2015: the default dovecot configuration files changed recently after Jessie became the new stable distribution of Debian, which caused some users problems; TLS on port 993 used to be enabled by default but now it isn't. We need to re-enable it. In /etc/dovecot/conf.d/10-ssl.conf, find ssl = no and change it to:

ssl = yes

There have been some security vulnerabilities discovered in older versions of the SSL protocol in recent times. SSLv2 is disabled by default, but it doesn't harm to explicitly disable it again. SSLv3 is vulnerable to an attack called POODLE, so we will disable it too. In the same file, find the ssl_protocols parameter line, uncomment it and add !SSLv3 to the end, like this:

ssl_protocols = !SSLv2 !SSLv3

Edit 02/09/2017: if you're using Debian Stretch or later, or one of its derivatives, then you will need to edit that line to match the following. The SSLv2 option is no longer recognised as an option for ssl_protocols because it has been removed entirely:

ssl_protocols = !SSLv3

For some bizarre reason, the Dovecot package for Raspberry Pi (and possibly newer versions of Ubuntu) does not create a self-signed certificate during installation like it used to. So, we have to create one manually. If you look in /usr/share/dovecot/ you will find the script that used to be used to generate the certificate; we can use it ourselves to simplify the process. The script is located at /usr/share/dovecot/mkcert.sh and looks like this:

#!/bin/sh

# Generates a self-signed certificate.
# Edit dovecot-openssl.cnf before running this.

OPENSSL=${OPENSSL-openssl}
SSLDIR=${SSLDIR-/etc/ssl}
OPENSSLCONFIG=${OPENSSLCONFIG-dovecot-openssl.cnf}

CERTDIR=/etc/dovecot
KEYDIR=/etc/dovecot/private

CERTFILE=$CERTDIR/dovecot.pem
KEYFILE=$KEYDIR/dovecot.pem

if [ ! -d $CERTDIR ]; then
  echo "$SSLDIR/certs directory doesn't exist"
  exit 1
fi

if [ ! -d $KEYDIR ]; then
  echo "$SSLDIR/private directory doesn't exist"
  exit 1
fi

if [ -f $CERTFILE ]; then
  echo "$CERTFILE already exists, won't overwrite"
  exit 1
fi

if [ -f $KEYFILE ]; then
  echo "$KEYFILE already exists, won't overwrite"
  exit 1
fi

$OPENSSL req -new -x509 -nodes -config $OPENSSLCONFIG -out $CERTFILE -keyout $KEYFILE -days 365 || exit 2
chmod 0600 $KEYFILE
echo 
$OPENSSL x509 -subject -fingerprint -noout -in $CERTFILE || exit 2

If you were going to use this certificate for any significant length of time, it would be worth editing the parameters in the config file it uses (/usr/share/dovecot/dovecot-openssl.cnf) to set the proper common name and contact details on the certificate. However, I suggest you leave the defaults as they are, use this certificate just for testing, and then come back later and generate a new cert when everything is working (more on that later). You must be in the same folder as the configuration file when you run the script, or it will not find the config and the certificate generation will fail. The following two commands will change to the right folder and then execute the script:

cd /usr/share/dovecot
sudo ./mkcert.sh

You should see a message "writing new private key to '/etc/dovecot/private/dovecot.pem'" and then some details about the certificate. Next, find the following two lines in /etc/dovecot/conf.d/10-ssl.conf and uncomment them:

#ssl_cert = </etc/dovecot/dovecot.pem
#ssl_key = </etc/dovecot/private/dovecot.pem

Now reload dovecot to apply the changes:

sudo service dovecot reload

Since IMAPS is a connection over SSL/TLS, we can’t use Telnet to test it. Instead, we use openssl to create a secure connection. There are two versions of the command, one will show you LOADS of information about the certificate used to encrypt the connection, and the other will suppress this info. I recommend trying the long version out of interest, but both will work the same for the test: For full information:

openssl s_client -connect localhost:993

For minimal information:

openssl s_client -connect localhost:993 -quiet

I won’t print the output of the first command, because it’s ridiculously long. Here’s an example of the second, including a login test:

admin@samhobbs /etc/dovecot/conf.d $ openssl s_client -connect localhost:993 -quiet
depth=0 O = Dovecot mail server, OU = samhobbs, CN = samhobbs, emailAddress = root@samhobbs.co.uk
verify error:num=18:self signed certificate
verify return:1
depth=0 O = Dovecot mail server, OU = samhobbs, CN = samhobbs, emailAddress = root@samhobbs.co.uk
verify return:1
* OK [CAPABILITY IMAP4rev1 LITERAL+ SASL-IR LOGIN-REFERRALS ID ENABLE IDLE AUTH=PLAIN AUTH=LOGIN] Dovecot ready.
a login "testmail" "test1234"
a OK [CAPABILITY IMAP4rev1 LITERAL+ SASL-IR LOGIN-REFERRALS ID ENABLE IDLE SORT SORT=DISPLAY THREAD=REFERENCES THREAD=REFS MULTIAPPEND UNSELECT CHILDREN NAMESPACE UIDPLUS LIST-EXTENDED I18NLEVEL=1 CONDSTORE QRESYNC ESEARCH ESORT SEARCHRES WITHIN CONTEXT=SEARCH LIST-STATUS SPECIAL-USE] Logged in
b logout
* BYE Logging out
b OK Logout completed.
Connection closed by foreign host.

Good stuff: SSL/TLS is working on port 993, and you can log in successfully. Note that by default Dovecot uses a “snakeoil” self-signed certificate. SSL/TLS certificates are used for two purposes: encryption and verification. The “snakeoil” certificate will encrypt your content but it won’t verify that you’re talking to your server – you could be talking to someone imitating your server (anyone can create a self-signed certificate claiming to be any website). If you’d like to get your certificate signed without forking out loads of money to a cert signing authority, I’d recommend CAcert. I've written a tutorial explaining how to generate your own cert and get it signed here. If you opt for a commercial certificate, you can use the CAcert tutorial to generate the certificate and then this tutorial will explain the differences in the installation/configuration of commercial certificates once you have it signed. If you're testing a proper certificate, use this command to tell openssl where the trusted root certificates are stored:

openssl s_client -connect localhost:993 -quiet -CApath /etc/ssl/certs

Tidying up and enabling WAN access

Before opening the ports on your router to the world, it’s a good idea to delete that test user because the password is so easy to guess.

sudo userdel testmail

Also, if you still use the "pi" login, for goodness' sake change the password from "raspberry"! You can do this using the passwd command when logged in as pi:

passwd

Or you can achieve the same thing when logged in as another user by using sudo to gain root privileges:

sudo passwd pi

Now you can open a few ports on your router’s firewall. Make sure your Pi has a static LAN IP address and then forward these ports from WAN to its LAN IP address:

  • Port 25 for SMTP (used for receiving emails)
  • Port 465 for secure SMTP (used for sending emails after SASL authentication)
  • Port 993 for IMAPS (used to receive emails on your phone/tablet/computer)

Here’s an example on my router, running OpenWrt: openwrt-port-forwards-raspberry-pi-email-server.png

Setting up IMAP Email Clients

I’m now going to run through setting up IMAP email clients quickly, using K9 Mail on Android and Thunderbird on GNU/Linux as examples. The setup for Thunderbird on Windows and Mac OSX should be very similar. The basics are this:

  • Select an IMAP connection
  • Your login is your username only (omit @yourdomain.com), and you password is…your password!
  • For incoming emails: select use SSL/TLS always and the program should automatically select port 993
  • For outgoing emails: select SSL/TLS always. The program may suggest port 587, but you want port 465

K9 Mail

Open K9 Mail and select add new account. Type in your account information (you@yourdomain.com and password) and then select manual setup. Select IMAP and then enter your information as follows… Incoming email: K9 Incoming Email Settings Outgoing email: K9 Outgoing Email Settings

Thunderbird

Open Thunderbird, and then click Account Actions –> Add Mail Account. Fill in your password and email address, which is your username followed by your fully qualified domain name (FQDN), i.e. username@yourdomain.com: Thunderbird Step 1: Mail Account Setup Thunderbird will try to auto-detect settings and fail. Don’t worry, this is normal. Select “manual config”:  Thunderbird Step 2: TB will try to autodetect settings, and fail. Select “Manual Config" Now edit the settings as appropriate. I had to remove a period (.) from in front of my “server hostname”, and edit the SSL and Authentication settings. If you select “SSL/TLS” for both incoming and outgoing, ports 993 and 465 are automatically selected: Thunderbird Step 3: Edit the settings so that they match these (but change them to match your username and domain name!) Now try emailing yourself from your external email address, and see if your email gets through. If you are having problems, be sure to check you’ve set up an MX record as well as a DNS A record.

Stuck in spam filters?

A few people have contacted me recently to say that their email server is working fine but their emails are getting sent to Gmail's spam folder. If you are experiencing problems like this (or even if you're not), try setting up an SPF and/or PTR record as explained in my DNS basics tutorial. You might also want to check if your domain name or IP address are on any blacklists. There's a handy website called MX toolbox that lets you do this (choose blacklist check from the dropdown menu).

Almost done…

Good news! If you’ve reached this far and everything is working, then you’re almost done. The next step (Webmail with Squirrelmail) is optional but by far the easiest of the three steps. If you’ve hit a rut, please post a comment and I’ll try and help you out. If not… continue to Raspberry Pi Email Server Part 3: Squirrelmail

Comments

Thanks for the response, Sam. Yes, port 993 is forwarded and it is the first time I've attempted to connect to my mail server remotely. I've fixed the issue (though I don't know what the actual issue is!). If I connect to my mail server's ip address I can collect my email. It only fails if I use the domain name.

Warren Moore

Mon, 11/10/2014 - 18:00

I've been following the guide and I've ran into an error when I try to test IMAP. When I select "b select inbox:", I get the following: - b NO [SERVERBUG] Internal error occurred. Refer to server log for more information. [2014-11-10 12:55:49]. I'm very much a newbie with linux and with email servers, but I'm learning...slowly :)

So I decided to try over again...so far all seemed to go well....until...... Time to try openssl
I type in pi@raspberrypi ~ $ openssl s_client -connect localhost:465 -quiet

The response is depth=0 CN = raspberrypi
Shouldn't the CN be my network name....

looks like uncommented the wrong line in /etc/dovecot/conf.d/10-mail.conf. Have it working now other than a glitch with saving sent emails to sent folder...but that looks like it might a Thunderbird error...no such error in Kaiten. Now for spamassassin...wish me luck :D

Dear Sam,
Many thanks for your terrific articles which greatly assisted me in the difficult task of setting up a mail server on my raspberry pi.
Forgive me if this was covered in other comments, but are you able to advise how I might add user accounts? I'm using Icedove (rebranded Thunderbird) as my client.
Currently the only user recognised by Postfix / Dovecot is 'pi' which is the default user name. I would like to add additional user accounts so that emails may be received separately e.g. 'grant@baileyandireland.com', 'jenn@baileyandireland.com', etc.
Are you able to point me in the right direction.
Thanks and well done,
Grant Bailey

Hi grant, You can use the adduser command, which is the one we used to add the test user in this tutorial, i.e.:
sudo adduser grant
sudo adduser jenn
If you haven't already done so, you should change the password for the user pi from the default of "raspberry". If you need to modify the password you can use this command:
sudo passwd pi
Sam

Sam,

Many thanks. Postfix / Dovecot automatically created folders for the new users, the secret was to log out of my Pi and log in again as the new user. I was then able to have Icedove connect to the account of the new user.

Do you drink wine? I'd like to send you some as thanks for the substantial effort you made to publish these articles, which were tremendously helpful to me. Please send me your mailing address by private email.

Regards,

Grant

Glad it's all working! I drink a tremendous amount of wine :p that would be really kind! Here's a neat trick, on your pi you can use the whois command to get information about who registered the domain for a website:
whois samhobbs.co.uk
You can register through another company if you don't want your info to be public (the command would then show that company's address) but I didn't really understand at the time... so there you go! Sam

Just a warning that gmail will refuse to deliver the emails if you follow the tutorial above due to RFC 2822, which says that you must include a "From:" line in the data (and a "Date:" technically).


mail from: foo
rcpt to: bar@gmail.com
data
From: foo@yourdomain.com
Subject: test
Just a test
.

After i wanted to test openssl it answer with this:

openssl s_client -connect localhost:465 -quiet
depth=0 CN = raspberrypi
verify error:num=18:self signed certificate
verify return:1
depth=0 CN = raspberrypi
verify return:1
220 roethlisberger.me ESMTP Postfix (Debian/GNU)
quit
221 2.0.0 Bye

Not with my domain, instead with raspberrypi...
Is this important that there is my domain or what do i need to do?

What is wrong when i recive this error?

telnet localhost 143
Trying 127.0.0.1...
Connected to localhost.
Escape character is '^]'.
* OK [CAPABILITY IMAP4rev1 LITERAL+ SASL-IR LOGIN-REFERRALS ID ENABLE IDLE STARTTLS AUTH=PLAIN AUTH=LOGIN] Dovecot ready.
a login "testmail" "test1234"
a OK [CAPABILITY IMAP4rev1 LITERAL+ SASL-IR LOGIN-REFERRALS ID ENABLE IDLE SORT SORT=DISPLAY THREAD=REFERENCES THREAD=REFS MULTIAPPEND UNSELECT CHILDREN NAMESPACE UIDPLUS LIST-EXTENDED I18NLEVEL=1 CONDSTORE QRESYNC ESEARCH ESORT SEARCHRES WITHIN CONTEXT=SEARCH LIST-STATUS SPECIAL-USE] Logged in
b select inbox
b NO [SERVERBUG] Internal error occurred. Refer to server log for more information. [2014-12-14 00:34:24]

Thanks for your fast answer!!!

My outputs:

insgesamt 8
drwx------ 2 testmail testmail 4096 Dez 14 00:32 mail
drwx------ 10 testmail testmail 4096 Dez 14 00:09 Maildir
lrwxrwxrwx 1 testmail testmail 44 Dez 14 00:09 pistore.desktop -> /usr/share/indiecity/pistore/pistore.desktop
pi@raspberrypi ~ $
pi@raspberrypi ~ $ cat /etc/dovecot/conf.d/10-mail.conf | grep mail_location
# path given in the mail_location setting.
mail_location = maildir:~/Maildir
# mail_location = mbox:~/mail:INBOX=/var/mail/%u
# mail_location = mbox:/var/mail/%d/%1n/%n:INDEX=/var/indexes/%d/%1n/%n
mail_location = mbox:~/mail:INBOX=/var/mail/%u
# mail_location, which is also the default for it.

Thanks for your help :)

Hi Sam,

Firstly thanks for these tutorials I am finding them very valuable. You should consider putting a bitcoin address on your website to receive donations!

I do have a question. I think I have everything configured correctly up to this point however because my IP is dynamic I am finding emails I send out are being rejected. I get a message that I should use my ISP's relay. My ISP is btinternet. I wondered if you have any hints how I do that ?

Thanks

You're welcome! I've never thought of doing the Bitcoin thing before, might be something worth looking into - I know very little about it and it could be interesting to learn! Have a look at this comment to see if it helps with the relay (it only works if it's an unauthenticated relay though and I'm not sure what the deal is with BT so check first!). If it's an authenticated relay the configuration is a little different so let me know and I'll give you some more detailed instructions. I'm with PlusNet (who are owned by BT) and a static IP address cost me a one off admin fee of £5 so that might actually be a better option for you because it solves the root of the problem... see if it's a similar price with BT? Sam

Yes you should check out bitcoin, from a technological perspective I think you might enjoy the idea of decentralised money protected by cryptography.

Back to the point I am keen to remain using dynamic IP if I can, I use FreeDNS with a cron job which updates the IP if it changes which seems to work well from my requirements. I've set the relay host as described in the comment you linked but it turns out authentication is required. I assume I'll have to configure username and password somewhere ? Still looking into that,

thanks again for help :)

A while ago I read into it quite a bit and liked the idea, I just haven't actually done anything with it. And if we know one thing here, it's that it's easiest to learn by doing, right? :) I'll add it to my list of things to check out! OK so back on topic there are a couple more steps for authenticated relaying. This link suggests that the hostname and port number you need are mail.btinternet.com and port 465. So in /etc/postfix/main.cf set:
relayhost = mail.btinternet.com:465
Now we need to create a file to hold your BT username and password. Create it with sudo nano /etc/postfix/sasl_password and fill it in like this:
mail.btinternet.com:465 EMAIL@btinternet.com PASSWORD
... where EMAIL is your BT username (I'm guessing your email address is something like user@btinternet.com but I don't have one so I'm not sure...) and PASSWORD is your password. Then we need to create a database so that postfix can read the password. This is done with postmap using:
sudo postmap /etc/postfix/sasl_password
...which creates a database at /etc/postfix/sasl_password.db Now we need to add a few more parameters to /etc/postfix/main.cf. In general, if the parameter has smtp_ at the start it's to do with postfix sending as a client (outgoing email to other servers), and smtpd_ is the SMTP daemon, for when Postfix is receiving email as the server in a transaction. So the following parameters only affect outgoing email... This one tells postfix it needs to use SASL to authenticate
smtp_sasl_auth_enable = yes
This one tells postfix to look up the PW in the database we just created:
smtp_sasl_password_maps = hash:/etc/postfix/sasl_password
This one is to override the default option, because it doesn't allow plaintext:
smtp_sasl_security_options = noanonymous
(the default is noplaintext, noanonymous but we'll be using TLS so plain text is fine) This tells your server it needs to use TLS when sending email:
smtp_tls_security_level = encrypt
...then cross your fingers and your toes, and do:
sudo service postfix restart
It's possible that something will go wrong here because I haven't tested it myself (I don't need a relay). I think it will work but it might not, so please let me know how you get on! Sam

Hi Sam, you got me going down the right track, I think I finally have it working.

Initially my emails were just disappearing after being sent, then i noticed warnings and errors in the logs using tail -f /var/log/mail.log
such as

warning: process /usr/lib/postfix/smtp pid 9874 exit status 1
warning: /usr/lib/postfix/smtp: bad command startup -- throttling

At one point I added smtp_sasl_password_maps = hash:sasl_password
into the config, I not sure but maybe i can take that out again.

Anyway I did rougly everything you said but there were a couple of minor differences in the end which got it working.

In the file sasl_password there is a colon : not a space between the username and the password, and the format for the relayhost in main.cf and in sasl_password has square brackets like this [mail.btinternet.com]:465

so my sasl_password looked like this in the end
[mail.btinternet.com]:465 user@btinternet.com:password

Anyway very happy to have this working and thanks so much for your tutorials. I'll probably try and get signed cert next, then squirrel mail, so will be frequenting your site for a while yet.

Cheers

Adrian

Great stuff, glad it's all working now and thanks for the corrections. It's quite a common question so I'll probably write it up sometime soon, your amendments will be really useful! Sam

Ah well, I spoke too soon last night :( Its not working afterall. The test emails that I received had been sent from the wrong account. oops! well it was quite late. I'm sure I'm almost there and thanks to you I'm on the right lines. About to have another crack at it.

Found some extra info on this link, https://anothersysadmin.wordpress.com/2009/02/06/postfix-as-relay-to-a-…
so added a couple of extra bits into the config from there.

Was getting messages in the log like this

postfix/smtp[19967]: CLIENT wrappermode (port smtps/465) is unimplemented
postfix/smtp[19967]: instead, send to (port submission/587) with STARTTLS

So have changed the port to 'submission' which equates to 587

postfix/smtp[19747]: warning: mail.btinternet.com[65.20.0.43]:587 offered no supported AUTH mechanisms: 'LOGIN'
postfix/smtp[19747]: warning: mail.btinternet.com[65.20.0.43]:587 offered no supported AUTH mechanisms: 'LOGIN PLAIN'

Now i think i need to change to STARTTLS or something ..

Will let you know how I get it working (assuming I manage it eventually)

Add new comment

The content of this field is kept private and will not be shown publicly.

Filtered HTML

  • Web page addresses and email addresses turn into links automatically.
  • Allowed HTML tags: <a href hreflang> <em> <strong> <cite> <blockquote cite> <code> <ul type> <ol start type> <li> <dl> <dt> <dd>
  • Lines and paragraphs break automatically.